教育用ロボット、研究用ロボット、競技用ロボット、ROBOTIS、DYNAMIXEL、DARWIN-OP、DARWIN-MINI、ロボット部品、プロショップ、ロボット販売

dynamixel、ダイナミクセル、サーボ、ロボットサーボ、アクチュエータ、コマンド式、デイジーチェーン、ROBOTIS、ロボティス dynamixel、ダイナミクセル、サーボ、ロボットサーボ、アクチュエータ、コマンド式、デイジーチェーン、ROBOTIS、ロボティス

安定化電源/バッテリー/充電器

表示件数:
1

(カテゴリ内:15点)

  • Little Fuse 125V 10A (LFU-10) 10pcs[903-0178-000]
    Little Fuse 125V 10A (LFU-10) 10pcs[903-0178-000]

    Little Fuse 125V 10A (LFU-10) 10pcs[903-0178-000]

     

     

    ■ 特徴

     

      - CM-510 / CM-700用のヒューズ

     

     

    ■ 構成品

     

      - ヒューズ : 10個

     

     

    ■ 容量

     

      - 125V 10A

     

     

    ■ 適用可能な製品

     

      - CM-510, CM-700

    583円
    注文数:
  • 電源供給基板 SMPS2Dynamixel[902-0034-000]
    電源供給基板 SMPS2Dynamixel[902-0034-000]
    USB2DynamixelとDYNAMIXELアクチュエータ接続時にSMPS(安定化電源)から電力を供給するためのハブ基板です。

    【メーカー】
    ROBOTIS 

    【商品の特徴】 

     ・USB2DynamixelにDYNAMIXELサーボモータを接続した場合、USBポートからはサーボを駆動(ブート含む)できるだけの電力は供給されないので、外部から電源を供給する必要があります。SMPS2Dynamixelを使用すればDynamixel接続ラインに直接VCCを供給できます。
     ・大容量のキャパシタを搭載しており、サーボモータを駆動した際の電圧降下を軽減します。

    【技術情報】

    USB2Dynamixel e-Manual
    1,122円
    注文数:
  • Robot Cable-2P 150mm (Battery Box) 4pcs[903-0192-000]
    Robot Cable-2P 150mm (Battery Box) 4pcs[903-0192-000]
    ROBOTIS MINI、OPENCM用の電源ケーブルです。
    1,540円
    注文数:
  • Li-ion Battery Charger Set LBB-041 [903-0221-000]
    Li-ion Battery Charger Set LBB-041 [903-0221-000]
    LB-040、LB-041用専用充電スタンド兼電池ボックス

    色は薄い水色がかっています。マイクロUSB端子経由で充電。 

    電池が抜けにくくなり、安全性も更に向上しました。
    今後は改良されたLBB-041をお買い求めください。

    ■説明
    DARWIN-MINIのキットにも付属している充電スタンドです。
    マイクロUSB端子経由でLB-040やLB-041を1本充電できます。
    本体にはOLLO規格の穴が空いており、2本線の電源ケーブルも付属しますのでマイコン工作や自作ロボット用の電池ボックスとしても最適です。

    ※USBケーブルに給電をする充電器は別途ご用意下さい。
    容量が1A程度あれば十分です。

    ■内容
    1)充電スタンドLBB-041本体 :1個
    2)マイクロUSBケーブル(USBオス-マイクロUSBオス):1本
    3) 電源線Robot Cable-2P(100mm) :1本

    ■技術情報

    動作内容:
    1)赤LED全点灯 → 充電中
    2)赤LED消灯 → 充電完了

    注意:
    ※複数のLBB-041を直列で接続した状態で、複数口を持つUSB充電器を接続し充電を行わないで下さい。
    複数口のUSB充電器は内部でGND共通となっているため、LB-041同士でショートしてしまいます。
    必ず、別々のUSB充電器をご使用下さい。

    ※ロボットコントローラー(CM-904等)にLBB-041を接続した状態で充電を行わないで下さい。
    1,551円
    在庫数 : 0
  • Li-POバッテリーチャージャー LBC-010[903-0144-000]
    Li-POバッテリーチャージャー LBC-010[903-0144-000]
    Li-POバッテリー2セル、3セル対応のバランス充電器。コンパクトサイズで場所をとりません

    【メーカー】

    ROBOTIS 

    【商品の特徴】 

     ・Li-POバッテリー専用充電器。
     ・2セル(7.4V)と3セル(11.1V)の両方に対応(※同時に充電はできません。)
     ・バッテリーのバランス端子を接続してバランス充電を行います。端子を差すだけで充電スタートの簡単操作。
     ・充電出力電流 約1000mA、BIOLOIDのバッテリーを残量が減った常態でも1時間以内に満充電に出来ます。
     ・安定化電源 SMPC 12V 5A PS-10が別途必要があります。
    2,090円
    注文数:
  • Li-ion Battery 3.7V 2600mAh LB-041 [903-0220-002]
     Li-ion Battery 3.7V 2600mAh LB-041 [903-0220-002]
     Li-ion Battery 3.7V 2600mAh LB-041 [903-0220-002]
    ROBOTIS MINI用の新型大容量バッテリーです。
    従来のバッテリー903-0220-001の倍の容量
    Features

    Lithium-ion rechargeable battery.

    PCM is incorporated to protect the battery from overcharge, discharge, and excessive current. Battery cover (blue) included for safety.

     
    Package Components
    Li-ion Battery 3.7V 2600mAh LB-0411
     

    * Battery charger (LBB-041) sold separately

    H/W Specifications
    Weight50g
    Size24mm x 70mm x 27mm
    Voltage3.7V
    Capacity2600mAh
    Etc.

    Cell type Li-ion 18650

    PCM built-in (overcharge, discharge, excessive current protection)

    Compatible Products

    Controller : CM-150/151, OpenCM9.04

    Battery Charger : Li-ion Battery Charger Set LBB-040, Li-ion Battery Charger Set LBB-041

    - This battery can NOT be connected directly to the controller.

    You will need the Li-ion Battery Charger Set (LBB-041) to connect to the controller (robot).

    Storage Precautions

    Detach the battery from the robot or controller when storing away.

    When storing away the battery for a long time, make sure the battery life is around 50%.

    Do not store it in wet or hot places.


    ※ The warranty for Li-ion Battery 3.7V 2600mAh LB-041 is 6 months.

    Caution

    - Do not drop or give impact.

    - Do not operate while charging.

    - Do not apply heat, water or any other liquid on the battery.

    - Do not place in the microwave, washing machine or dryer.

    - Do not use damaged batteries (inflated, deformed, damaged, etc.).

    - Do not short circuit the polarity.

    - Do not take the battery apart.

    - When charging, make sure the battery is connected to the correct polarity.

    - Do not charge when the battery is hot. Please charge after it has cooled off.

    - Do not keep the battery connected to the controller when not in use.

     
     

    ※ LB-041(New Li-ion battery) cannot be recharged with LBB-040(Old Li-ion battery charger).


    ※ LBB-041(New Li-ion battery charger) can be recharged with LB-040(Old Li-ion battery).

    2,970円
    在庫数 : 0
  • Balance Charger for 7.4-11.V 2-3S Cells Li-Po Battery
    Balance Charger for 7.4-11.V 2-3S Cells Li-Po Battery
    Balance Charger for 7.4-11.V 2-3S Cells Li-Po Battery

    ROBOTISのヤントンの青いのよりも更にちいさくお洒落
    LEDが赤(通電中)、緑点灯(充電中)、緑淡い点滅(充電完了)
    別売の12V7A安定化電源による給電により
    2000mA以下の充電式Lipoをチャージ可能です。
    充電電流は0.8Aであるため、心に余裕がある方にお勧め。
    バランスコネクターからの充電で設定など全くないので、
    最も安全な充電システムの一例です。
    3,300円
    在庫数 : 0
  • DARwIn-OP用Li-POバッテリー LB-011[903-0143-001]
    DARwIn-OP用Li-POバッテリー LB-011[903-0143-001]
    DARwIn-OP用純正バッテリー

    過放電などを防止する保護回路を内蔵しています。その実力はROBO CUP世界大会で実証済み。他社、自作の3Kgサイズの二足歩行ロボットに最適です。

    【メーカー】

    ROBOTIS 

    【商品の特徴】 

     ・DARwIn-OP用純正バッテリー
     ・11.1V 1000mAh 10C
     ・過充電、過放電、過電流防止の保護回路内蔵
     ・専用充電器 LBC-10を使用すれば1時間以内での充電が可能。

    【適合製品】

    ・充電器
     Li-POバッテリーチャージャー LBC-10
    ※充電を行うには安定化電源 SMPS 12V 5A PS-10が別途必要です。

    【主な仕様】

    ・重さ     :83g
    ・本体サイズ :約70mm×36mm×21mm

    ・セル数      :3セル
    ・電圧       :11.1V
    ・容量       :1000mAh   
    ・瞬間放電能力 :10C 

    ・保護回路(PCM)機能 :過充電、過放電、過電流防止

    ・コネクタ
     模型用大電流対応T型コネクター
     バランス充電端子


    【商品内容】

    ・バッテリー LB-011  :1個

    ※充電器は別売です。
    4,037円
    注文数:
  • U2D2 PHB Set[902-0145-001]
    U2D2 PHB Set[902-0145-001]
    U2D2 PHB Set[902-0145-001] 
    待望のハブ型電源供給基板登場です。
    Xシリーズのコネクターを3つずつ配し、
    2種の電源供給ラインを持ち、スイッチ付きです。
    U2D2と合体出来システムがスッキリします。
    ご要望の多かった合体に必要なROBOT CABLE X3P100mmや
    X4P 100mmが付属します。
    U2D2は別売ですのでご注意ください・
    Features

    The U2D2 Power Hub Board combines with the U2D2 to supply a variety of external power sources to DYNAMIXELs.

    The board is capable of supplying power to all DYNAMIXELs with the SMPS port, terminal block, and 2P power connector.

    The board has holes to fix the U2D2 module and can be assembled using the rivets supplied in the package.

    -Easily powers ON/OFF with the power switch


    *Robot cable for connecting U2D2 is included.

    Package Components
    U2D2 Power Hub Board1
    Rivet (For U2D2 assembly )1
    NUT M34
    Support M3x10x64
    Robot Cable-X3P 100mm1
    Robot Cable-X4P 100mm1

    *U2D2 is not included.
    H/W Specifications
    Dimension48mm x 57mm
    Operating Voltage7.4V ~ 24.0V
    Max Current10.0A
    Compatible Products
    DYNAMIXEL AX/MX-Series, PRO-Series

    - Use the Molex-JST Convertible Cable (Use 3P or 4P based on your communication selection)


    DYNAMIXEL X-Series, PRO+ Series

    - Use the JST Cable. (Use 3P or 4P based on your communication selection)


    The U2D2 Power Hub Board only has a JST type connector and requires a convertible cable when connecting to Molex type connectors. 

    *Required cables: Min 2pcs (U2D2 <-> DYNAMIXEL,
    U2D2 Power Hub Board <-> DYNAMIXEL)
    Caution
    U2D2 is not included
    When using the terminal block, please pay attention to the polarity when using external power.
    Left side is - and Right side is +
    Various pins are exposed behind the board. We recommend users to assemble and use the included supporter.
    Links
    4,180円
    注文数:
  • LIPO Battery 11.1V 1300mAh LB-020 [903-0277-000]
     LIPO Battery 11.1V 1300mAh LB-020 [903-0277-000]
    ROBOTIS ENGINEER用のLiPoバッテリーです。

    Features

    This LiPo battery is intended for Engineer Kits.

    PCM is incorporated to protect the battery from overcharge, discharge, and excessive current.

    Can be recharged with LBC-010 Battery Charger.

    Package Components
    LIPO Battery 11.1V 1300mAh LB-0201
    EF25-F271
    EF25-F261
    Battery Extension Cable1

    *Battery Charger sold separately
    H/W Specifications
    Weight102g
    Size70mm x 36mm x 24mm
    Voltage11.1V
    Capacity1300mAh
    Discharge Rate15C
    Etc.PCM built-in (Overcharge,Discharge,Excessive Current Protection)
    Compatible Products

    Controller : CM-510, CM-530, CM-700, CM-550

    Charger : LIPO Battery Charger LBC-010

    CM-100, CM-5, CM-2+, CM-150, CM-200 , OpenCM7.0 are not compatible

    Storage Precautions


    Detach the battery from the robot or controller when storing away.

    When storing away the battery for a long time, make sure the battery life is around 50%.
    Store it out of direct sunlight between 0 and 45 degrees.

    Do not store it in wet or hot places.

    Do not store with metal items such as coins, keys, necklaces

    ※ The warranty for LI-PO Battery 11.1V 1300mAh LB-020 is 6 months.

    Caution

    Do not drop or fold parts of the battery or its parts.

    Do not use the product when charging.

    Do not apply heat, water or any other liquid on the battery.

    Do not place in the microwave, washing machine or dryer.

    Do not use damaged batteries. (inflated,deformed, damaged, etc)

    Do not short circuit the polarity.

    Do not take the battery apart.

    When charging, make sure the battery is connected into the correct polarity.

    Do not charge when the battery is hot. Please charge after it has cooled off.

    When the battery is not being used or fully charged, please do not have it connected to a controller.

    Do NOT charge the battery when the battery is connected to the controller.

    4,873円
    注文数:
  • 6 Port TTL(3PIN) Power Hub
    6 Port TTL(3PIN) Power Hub
    HUB機能を備えた優れものの電源供給基板です。
    TTL3PIN 6port TROSSEN製品

    The 6 Port AX/MX Power Hub is a must have accessory for any DYNAMIXEL user. This little board is a Bioloid 6 Port Hub and a 

    5,500円
    在庫数 : 1
    注文数:
  • 6 Port RS485(4pin) Power Hub
    6 Port RS485(4pin) Power Hub
    HUB機能を備えた優れものの電源供給基板です。
    RS485 4PIN 6port TROSSEN製品

    The 6 Port RX/EX Power Hub is a must have accessory for any DYNAMIXEL user working with 4-pin servos. 

    The DYNAMIXEL communication bus allows you to daisy chain multi servos, making wiring a breeze. However sometimes you need to split your DYNAMIXEL chain into multiple directions. Just plug a 4-Pin Dynamixel Cable from your controller to any port on the hub, and you'll have 5 ports available for DYNAMIXEL's 4-pin servos.

    This hub has the added benefit of 2 power breakouts. You can plug in bare wire with the screw terminal block, or plug in power through the DC barrel jack. The 2.1*5.5 female barrel jack will accept any of our SMPS power supplies as well as our Battery Wiring Harness.

    The RX/EX Power Hub is compatible with the following DYNAMIXEL servos:

    RX-24FRX-28RX-64MX-28RMX-64R*MX-106R*EX-106*

    This hub is NOT compatible with the all AX and 3-pin MX series of DYNAMIXEL servos.

    *Under certain circumstances, these servos can drop the voltage on Switched Mode Power Supplies. If you are using these servos with an SMPS we recommend also using the SMPS2DYNAMIXEL

    5,500円
    在庫数 : 0
  • 安定化電源SMPS AKA-12070(12V 7A)[JP3-0043-000]
    安定化電源SMPS AKA-12070(12V 7A)[JP3-0043-000]
    ご要望の多かった12V 7Aの安定化電源(SMPS)です。
    安定化電源SMPS AKA-12070(12V 7A)[JP3-0043-000]
    定格入力 (AC) : 100~240V 
    定格出力 (DC) : 12V 7A 
    効率基準 : レベル 6 (Efficiency Level VI) 
    取得規格 : PSE , BSMI , cUL , FCC , CE , GS 
     
    DCコード長 : 1,200mm 
    DCプラグ : φ5.5 × 2.5 × 9.5 (ストレート) 
    出力極性 : センタープラス 
    外形寸法 : 151 × 64 × 36mm 
    RoHS対応 : 対応 (10物質) 
    5,918円
    注文数:
  • ラージLi-POバッテリー LB-012[903-0210-000]
    ラージLi-POバッテリー LB-012[903-0210-000]
    DARwIn-OP及びTURTLEBOT3用ラージバッテリー、標準バッテリーの1.8倍の容量(1800mAh)
    3Kg以下の市販、自作の二足歩行ロボットにも最適です。

    【メーカー】

    ROBOTIS 

    【商品の特徴】 

     ・DARwIn-OP用純正バッテリー
     ・11.1V 1800mAh 5C
     ・過充電、過放電、過電流防止の保護回路内蔵
     ・専用充電器 LBC-10を使用すれば約2時間以内での充電が可能。
       ※急速充電器の使用をお薦めします。

    【適合製品】

    ・充電器
     Li-POバッテリーチャージャー LBC-10
    ※充電を行うには安定化電源 SMPS 12V 5A PS-10が別途必要です。

    【主な仕様】

    ・重さ     :83g
    ・本体サイズ :約70mm×36mm×21mm

    ・セル数      :3セル
    ・電圧       :11.1V
    ・容量       :1800mAh   
    ・瞬間放電能力 :5C 

    ・保護回路(PCM)機能 :過充電、過放電、過電流防止

    ・コネクタ
     模型用大電流対応T型コネクター
     バランス充電端子


    【商品内容】

    ・バッテリー LB-012  :1個

    ※充電器は別売です。
    7,656円
    注文数:
  • 無線機器用安定化電源器 DM-330MV
    無線機器用安定化電源器 DM-330MV
    Max 32A 無線機器用安定化電源器 DM-330MV
    ロボットコンテスト、研究用定番ACDCスイッチング電源
    スイッチング方式だから小型軽量高出力。15Vまで出力可変出来るので
    3CELL 11.1V LIPO電池採用時のテストが可能

    スイッチング方式採用により今までにない小型軽量化、そして連続30Aの安定供給を実現。わずらわしいノイズも回避出来る特許のノイズオフセット機能を搭載、もしもの場合でも各種の保護回路で接続機器を保護します。
    【ご注意】
    無線機器用の電源です。電気分解のような化学実験用途、コンプレッサやモーターを使う機器、突入電流が大きな特殊電球の点灯、バッテリーの充電にはお使いになれません。保護回路が働く前に故障することがあります。製品保証以外の責は負いかねますので、商・工業、学術用途でのご使用は自己責任とさせていただきます。

    AC100V、120V専用です。220V,240Vを印可するとすぐに壊れ、修理ができないダメージを受けますのでご注意ください。
    38,280円
    注文数:
1

(カテゴリ内:15点)

表示件数: