教育用ロボット、研究用ロボット、競技用ロボット、ROBOTIS、DYNAMIXEL、DARWIN-OP、DARWIN-MINI、ロボット部品、プロショップ、ロボット販売

dynamixel、ダイナミクセル、サーボ、ロボットサーボ、アクチュエータ、コマンド式、デイジーチェーン、ROBOTIS、ロボティス dynamixel、ダイナミクセル、サーボ、ロボットサーボ、アクチュエータ、コマンド式、デイジーチェーン、ROBOTIS、ロボティス

商品一覧

表示件数:
1 2 3 45 6 7 8 9 次へ >>

(全商品:430点)

  • DYNAMIXEL RX-64(RS485モデル) バルク6個セット[902-0015-000]
    DYNAMIXEL RX-64(RS485モデル) バルク6個セット[902-0015-000]
    DYNAMIXEL RX-64(RS485モデル) バルク6個セット[902-0015-000]
    2017年5月1日ROBOTISにより生産中止、修理等は承ります。
    RX-64のお得な6個セットです。サーボホーン、ケーブル等は付属しません。

    【メーカー】:ROBOTIS(ロボティーズ)

    【主な仕様】
    ・保持トルク: 52kgf・cm(18.5V、2.6A時)
    ・最大スピード: 64rpm(18.5V、無負荷時)
    ・重量: 72g
    ・サイズ: 40.2mm×61.1mm×41mm
    ・接続方式: RS-485/4線式


    ※RX-64 HN07-N101 TypeはMX-64Rより1世代古い旧製品です。
    新たにロボット製作をお考えの場合は最新モデルのMX-64Rをお勧めします。
    186,450円
    2017年5月1日ROBOTISにより生産中止、修理等は承ります。問い合わせください。
  • DYNAMIXEL AX-12+
    DYNAMIXEL AX-12+
    ※※※本製品はメーカー廃盤となりました、後継機種は「AX-12A」です。※※※

    【主な仕様】
    •Stall Torque:15kgf.cm(at 12.0V、1.5A)
    •No load speed : 59rpm(at 12V)
    •重量:53.5g
    •サイズ:32mm * 50.1mm * 40mm

    ※その他仕様については詳細ページをご参照ください。

    【AXシリーズ ROBOTIS e-マニュアル】

    DYNAMIXEL AXシリーズ ROBOTIS e-マニュアル
    0円
    メーカー廃盤品、「AX-12A」をお買い求めください。
  • DYNAMIXEL AX-18F
    DYNAMIXEL AX-18F
    ※※※本製品はメーカー廃盤となりました、後継機種は「AX-18A」です※※※

    【主な仕様】
    •Stall Torque:18kgf.cm(at 12.0V、2.2A)
    •No load speed : 97rpm(at 12V)
    •重量:54.5g
    •サイズ:32mm * 50.1mm * 40mm

    【AXシリーズ ROBOTIS e-マニュアル】

    DYNAMIXEL AXシリーズ ROBOTIS e-マニュアル

    ※その他仕様は詳細ページをご参照ください。
    0円
    メーカー廃盤品、「AX-18A」をお買い求めください。
  • PM42-010-S260-R [902-0091-001]
    PM42-010-S260-R [902-0091-001]
    PM54-040-S250-R[902-0089-001] 
    品薄です。納期は必ずご確認ください。
    Features
    DYNAMIXEL is a robot exclusive smart actuator with fully integrated DC Motor + Reduction Gearhead + Controller + Driver + Network in one DC servo module.

    DYNAMIXEL-P Series implements removable reduction cycloid gears, resulting in high precision and impact resistance.

     

    - Torque control based on current sensing

    - Position, Torque and Speed-based command

    - High resolution with combination of Incremental Encoder and Contactless Absolute Encoder

    - Full metal housing for high durability

    - Can be used to make a full-size manipulator, pan tilt, humanoid, etc.


    [DYNAMIXEL PRO -> P] Upgrade Details

    - Improved design and JST connectors applied

    - Improved dirt inflow and leakage

    - Improved control table (Supports X Series functions) 

    - Enhanced control performance such as responsiveness and resolution

    - Enhanced communication responsiveness

    - Improved heat, noise, and durability

    Package Components
    PM42-010-S260-R1
    Robot Cable-X4P 300mm(Convertible)1
    Robot Cable-X4P 300mm1
    Wrench Bolt WB M3x820
    Compatible Products

    Controller : OpenCM 485 Expansion Board, OpenCR1.0

    Interface : USB2Dynamixel, U2D2

    Factory Default Settings

    ID : 1

    Baud Rate : 57600bps


    (User can change various settings including ID and baud rate according to environment)


     

    101,200円
    注文数:
  • PH42-020-S300-R[902-0081-001]
    PH42-020-S300-R[902-0081-001]

    PH42-020-S300-R[902-0081-001]
    品薄です。納期は必ずご確認ください。
    Features

    Dynamixel Pro series is a self-developed high performance all-in-one actuator equipped with a cycloid reducer.


    Torque control based on current sensing

    Increased reliability and accuracy for position and speed control through PID control

    High resolution with combination of Incremental Encoder and Contactless Absolute Encoder

    Full metal housing for high durability

    Can be used to make a full-size manipulator, pan tilt, humanoid, etc.


    [Dynamixel PRO ] Upgrade Details

    Improved design and JST connectors applied)

    Improved dirt inflow and leakage (54-Series)

    Improved control table (Supports X-series functions) 

    Enhanced control performance such as responsiveness and resolution

    Enhanced communication responsiveness

    Improved heat, noise, and durability

    Package Components
    PH42-020-S300-R1
    Robot Cable-X4P 600mm2
    Wrench Bolt WB M3x820
    Compatible Products

    Controller : OpenCM 485 Expansion Board, OpenCR1.0

    Interface : USB2Dynamixel, U2D2

    Factory Default Settings

    ID : 1

    Baud Rate : 57600bps


    (User can change various settings including ID and baud rate according to environment)

    Caution

    The operational voltage is different from other DYNAMIXEL series (Operational voltage: 24V).

    Depending on the number of units used, it is recommended to use a separate power supply.

    JST 4Pin connector is applied for communication.

    The 42 series uses the same hinge frames.(FRP42-H110/120)

    Specification
    Model NamePH42-020-S300-R
    MCUCortex-M4 (168 [Mhz], 32 [bit])
    Input VoltageMin. [V]-
    Recommended [V]24.0
    Max. [V]-
    Performance CharacteristicsVoltage [V]24.0
    Stall Torque [N·m]-
    Stall Current [A]-
    No Load Speed [rpm]32.7
    No Load Current [A]0.57
    Continuous OperationVoltage [V]24.0
    Torque [N·m]5.1
    Speed [rpm]29.2
    Current [A]1.5
    ResolutionResolution [deg/pulse]0.0006
    Step [pulse]607,500
    Angle [degree]360
    Position SensorContactless absolute encoder
    Incremental encoder
    Operating TemperatureMin. [°C]-5
    Max. [°C]55
    MotorCoreless (Maxon)
    Baud RateMin. [bps]9,600
    Max. [bps]10,500,000
    Control AlgorithmPID
    Gear TypeCycloid
    Gear MaterialPrecious Metal
    Case MaterialPrecious Metal
    Dimensions (WⅹHⅹD) [mm]42.0 X 84.0 X 42.0
    Dimensions (WⅹHⅹD) [inch]1.65 X 3.31 X 1.65
    Weight [g]340.00
    Weight [oz]11.99
    Gear Ratio303.8 : 1
    Command SignalDigital Packet
    Protocol TypeHalf duplex Asynchronous Serial Communication (8bit, 1stop, No Parity)
    Link (Physical)RS485 Multi Drop Bus
    ID0 ~ 252
    FeedbackPosition, Velocity, Current, Temperature, Voltage, External Port, etc
    Protocol version2.0
    Operating Mode / AngleTorque Control Mode
    Velocity Control Mode
    Position Control Mode
    Extended Position Control Mode
    PWM Control Mode
    Output [W]20
    Standby Current [mA]30


    189,750円
    在庫数 : 0
  • PM54-040-S250-R[902-0089-001]
    PM54-040-S250-R[902-0089-001]
    PM54-040-S250-R[902-0089-001]
    2個のみです。その後は品薄です。納期確認ください。
    Features

    DYNAMIXEL is a robot exclusive smart actuator with fully integrated DC Motor + Reduction Gearhead + Controller + Driver + Network in one DC servo module.

    DYNAMIXEL-P Series implements removable reduction cycloid gears, resulting in high precision and impact resistance.

     

    - Torque control based on current sensing

    - Position, Torque and Speed-based command

    - High resolution with combination of Incremental Encoder and Contactless Absolute Encoder

    - Full metal housing for high durability

    - Can be used to make a full-size manipulator, pan tilt, humanoid, etc.


    [DYNAMIXEL PRO -> P] Upgrade Details

    - Improved design and JST connectors applied

    - Improved dirt inflow and leakage

    - Improved control table (Supports X Series functions) 

    - Enhanced control performance such as responsiveness and resolution

    - Enhanced communication responsiveness

    - Improved heat, noise, and durability

    Package Components
    PM54-040-S250-R1
    Robot Cable-X4P 300mm(Convertible)1
    Robot Cable-X4P 300mm1
    Power Cable-2P 600mm1
    Wrench Bolt WB M3x820
    Compatible Products

    Controller : OpenCM 485 Expansion Board, OpenCR1.0

    Interface : USB2Dynamixel, U2D2

    Factory Default Settings

    ID : 1

    Baud Rate : 57600bps


    (User can change various settings including ID and baud rate according to environment)

    Caution

    The operational voltage is different from other DYNAMIXEL series (Operational voltage: 24V).

    Depending on the number of units used, it is recommended to use a separate power supply.

    Molex 4Pin connector is used for communication.

    Specification
    Model NamePM54-040-S250-R
    MCUCortex-M4 (168 [Mhz], 32 [bit])
    Input VoltageMin. [V]-
    Recommended [V]24.0
    Max. [V]-
    Performance CharacteristicsVoltage [V]24.0
    Stall Torque [N·m]-
    Stall Current [A]-
    No Load Speed [rpm]28.4
    No Load Current [A]1.32
    Continuous OperationVoltage [V]24.0
    Torque [N·m]3.9
    Speed [rpm]24.2
    Current [A]1.9
    ResolutionResolution [deg/pulse]0.0007
    Step [pulse]502,834
    Angle [degree]360
    Position SensorContactless absolute encoder
    Incremental encoder
    Operating TemperatureMin. [°C]-5
    Max. [°C]55
    MotorBLDC (Maxon)
    Baud RateMin. [bps]9,600
    Max. [bps]10,500,000
    Control AlgorithmPID
    Gear TypeCycloid
    Gear MaterialPrecious Metal
    Case MaterialPrecious Metal
    Dimensions (WⅹHⅹD) [mm]54.0 X 108.0 X 54.0
    Dimensions (WⅹHⅹD) [inch]2.13 x 4.25 x 2.13
    Weight [g]710.00
    Weight [oz]25.04
    Gear Ratio251.4 : 1
    Command SignalDigital Packet
    Protocol TypeHalf duplex Asynchronous
    Serial Communication (8bit, 1stop, No Parity)
    Link (Physical)RS485 Multi Drop Bus
    ID0 ~ 252
    FeedbackPosition, Velocity, Current, Temperature, Voltage, External Port, etc
    Protocol versionProtocol 2.0
    Operating Mode / AngleTorque Control Mode
    Velocity Control Mode
    Position Control Mode
    Extended Position Control Mode
    PWM Control Mode
    Output [W]40
    Standby Current [mA]40
    202,400円
    注文数:
  • PM54-060-S250-R[902-0088-001]
    PM54-060-S250-R[902-0088-001]
    PM54-060-S250-R[902-0088-001]
    品薄です。納期は必ずご確認ください。
    Features

    DYNAMIXEL is a robot exclusive smart actuator with fully integrated DC Motor + Reduction Gearhead + Controller + Driver + Network in one DC servo module.

    DYNAMIXEL-P Series implements removable reduction cycloid gears, resulting in high precision and impact resistance.

     

    - Torque control based on current sensing

    - Position, Torque and Speed-based command

    - High resolution with combination of Incremental Encoder and Contactless Absolute Encoder

    - Full metal housing for high durability

    - Can be used to make a full-size manipulator, pan tilt, humanoid, etc.


    [DYNAMIXEL PRO -> P] Upgrade Details

    - Improved design and JST connectors applied

    - Improved dirt inflow and leakage

    - Improved control table (Supports X Series functions) 

    - Enhanced control performance such as responsiveness and resolution

    - Enhanced communication responsiveness

    - Improved heat, noise, and durability

    Package Components
    PM54-060-S250-R1
    Robot Cable-X4P 300mm(Convertible)1
    Robot Cable-X4P 300mm1
    Power Cable-2P 600mm1
    Wrench Bolt WB M3x820
    Compatible Products

    Controller : OpenCM 485 Expansion Board, OpenCR1.0

    Interface : USB2Dynamixel, U2D2

    Factory Default Settings

    ID : 1

    Baud Rate : 57600bps


    (User can change various settings including ID and baud rate according to environment)

    Caution

    The operational voltage is different from other DYNAMIXEL series (Operational voltage: 24V).

    Depending on the number of units used, it is recommended to use a separate power supply.

    Molex 4Pin connector is used for communication.

    Specification
    Model NamePM54-060-S250-R
    MCUCortex-M4 (168 [Mhz], 32 [bit])
    Input VoltageMin. [V]-
    Recommended [V]24.0
    Max. [V]-
    Performance CharacteristicsVoltage [V]24.0
    Stall Torque [N·m]-
    Stall Current [A]-
    No Load Speed [rpm]33.1
    No Load Current [A]1.25
    Continuous OperationVoltage [V]24.0
    Torque [N·m]10.1
    Speed [rpm]28.3
    Current [A]3.0
    ResolutionResolution [deg/pulse]0.0007
    Step [pulse]502,834
    Angle [degree]360
    Position SensorContactless absolute encoder
    Incremental encoder
    Operating TemperatureMin. [°C]-5
    Max. [°C]55
    MotorBLDC (Maxon)
    Baud RateMin. [bps]9,600
    Max. [bps]10,500,000
    Control AlgorithmPID
    Gear TypeCycloid
    Gear MaterialPrecious Metal
    Case MaterialPrecious Metal
    Dimensions (WⅹHⅹD) [mm]54.0 X 126.0 X 54.0
    Dimensions (WⅹHⅹD) [inch]2.13 x 4.96 x 2.13
    Weight [g]855.00
    Weight [oz]30.16
    Gear Ratio251.4 : 1
    Command SignalDigital Packet
    Protocol TypeHalf duplex Asynchronous
    Serial Communication (8bit, 1stop, No Parity)
    Link (Physical)RS485 Multi Drop Bus
    ID0 ~ 252
    FeedbackPosition, Velocity, Current, Temperature, Voltage, External Port, etc
    Protocol versionProtocol 2.0
    Operating Mode / AngleTorque Control Mode
    Velocity Control Mode
    Position Control Mode
    Extended Position Control Mode
    PWM Control Mode
    Output [W]60
    Standby Current [mA]40
    215,050円
    注文数:
  • PH54-100-S500-R[902-0078-001]
    PH54-100-S500-R[902-0078-001]

    PH54-100-S500-R[902-0078-001] 

    品薄です。納期は必ずご確認ください。
    Features

    Dynamixel Pro series is a self-developed high performance all-in-one actuator equipped with a cycloid reducer.


    Torque control based on current sensing

    Increased reliability and accuracy for position and speed control through PID control

    High resolution with combination of Incremental Encoder and Contactless Absolute Encoder

    Full metal housing for high durability

    Can be used to make a full-size manipulator, pan tilt, humanoid, etc.


    [Dynamixel PRO ] Upgrade Details

    Improved design and JST connectors applied

    Improved dirt inflow and leakage (54-Series)

    Improved control table (Supports X-series functions) 

    Enhanced control performance such as responsiveness and resolution

    Enhanced communication responsiveness

    Improved heat, noise, and durability

    Package Components
    PH54-100-S500-R
    1
    Robot Cable-X4P 600mm2
    Wrench Bolt WB M3x820
    Compatible Products

    Controller : OpenCM 485 Expansion Board, OpenCR1.0

    Interface : USB2Dynamixel, U2D2

    Factory Default Settings

    ID : 1

    Baud Rate : 57600bps


    (User can change various settings including ID and baud rate according to environment)

    Caution

    The operational voltage is different from other DYNAMIXEL series (Operational voltage: 24V).

    Depending on the number of units used, it is recommended to use a separate power supply.

    JST 4Pin connector is applied for communication.


    The 54-series can NOT use the old hinge frames. 

    NOT COMPATIBLE with FRP54-H110/120/210/220)

    Specification
    Model NamePH54-100-S500-R
    MCUCortex-M4 (168 [Mhz], 32 [bit])
    Input VoltageMin. [V]-
    Recommended [V]24.0
    Max. [V]-
    Performance CharacteristicsVoltage [V]24.0
    Stall Torque [N·m]-
    Stall Current [A]-
    No Load Speed [rpm]33.3
    No Load Current [A]1.13
    Continuous OperationVoltage [V]24.0
    Torque [N·m]25.3
    Speed [rpm]29.2
    Current [A]5.5
    ResolutionResolution [deg/pulse]0.0004
    Step [pulse]1,003,846
    Angle [degree]360
    Position SensorContactless absolute encoder
    Incremental encoder
    Operating TemperatureMin. [°C]-5
    Max. [°C]55
    MotorBLDC (Maxon)
    Baud RateMin. [bps]9,600
    Max. [bps]10,500,000
    Control AlgorithmPID
    Gear TypeCycloid
    Gear MaterialPrecious Metal
    Case MaterialPrecious Metal
    Dimensions (WⅹHⅹD) [mm]54.0 X 108.0 X 54.0
    Dimensions (WⅹHⅹD) [inch]2.13 x 4.25 x 2.13
    Weight [g]740.00
    Weight [oz]26.10
    Gear Ratio501.9 : 1
    Command SignalDigital Packet
    Protocol TypeHalf duplex Asynchronous Serial Communication (8bit, 1stop, No Parity)
    Link (Physical)RS485 Multi Drop Bus
    ID0 ~ 252
    FeedbackPosition, Velocity, Current, Temperature, Voltage, External Port, etc
    Protocol version2.0
    Operating Mode / AngleTorque Control Mode
    Velocity Control Mode
    Position Control Mode
    Extended Position Control Mode
    PWM Control Mode
    Output [W]100
    Standby Current [mA]40


    328,900円
    在庫数 : 0
  • PH54-200-S500-R[902-0079-001]
    PH54-200-S500-R[902-0079-001]

    PH54-200-S500-R[902-0079-001]
    品薄です。納期は必ずご確認ください。
    Features


    Dynamixel Pro series is a self-developed high performance all-in-one actuator equipped with a cycloid reducer.


    Torque control based on current sensing

    Increased reliability and accuracy for position and speed control through PID control

    High resolution with combination of Incremental Encoder and Contactless Absolute Encoder

    Full metal housing for high durability

    Can be used to make a full-size manipulator, pan tilt, humanoid, etc.


    [Dynamixel PRO ] Upgrade Details

    Improved design and JST connectors applied

    Improved dirt inflow and leakage (54-Series)

    Improved control table (Supports X-series functions) 

    Enhanced control performance such as responsiveness and resolution

    Enhanced communication responsiveness

    Improved heat, noise, and durability

    Package Components
    PH54-200-S500-R1
    Robot Cable-X4P 600mm2
    Wrench Bolt WB M3x820
    Compatible Products

    Controller : OpenCM 485 Expansion Board, OpenCR1.0

    Interface : USB2Dynamixel, U2D2

    Factory Default Settings

    ID : 1

    Baud Rate : 57600bps


    (User can change various settings including ID and baud rate according to environment)

    Caution

    The operational voltage is different from other DYNAMIXEL series (Operational voltage: 24V).

    Depending on the number of units used, it is recommended to use a separate power supply.

    JST 4Pin connector is applied for communication.


    The 54-series can NOT use the old hinge frames. 

    NOT COMPATIBLE with FRP54-H110/120/210/220)

    Specification
    Model NamePH54-200-S500-R
    MCUCortex-M4 (168 [Mhz], 32 [bit])
    Input VoltageMin. [V]-
    Recommended [V]24.0
    Max. [V]-
    Performance CharacteristicsVoltage [V]24.0
    Stall Torque [N·m]-
    Stall Current [A]-
    No Load Speed [rpm]33.1
    No Load Current [A]1.65
    Continuous OperationVoltage [V]24.0
    Torque [N·m]44.7
    Speed [rpm]29.0
    Current [A]9.3
    ResolutionResolution [deg/pulse]0.0004
    Step [pulse]1,003,846
    Angle [degree]360
    Position SensorContactless absolute encoder
    Incremental encoder
    Operating TemperatureMin. [°C]-5
    Max. [°C]55
    MotorBLDC (Maxon)
    Baud RateMin. [bps]9,600
    Max. [bps]10,500,000
    Control AlgorithmPID
    Gear TypeCycloid
    Gear MaterialPrecious Metal
    Case MaterialPrecious Metal
    Dimensions (WⅹHⅹD) [mm]54.0 X 126.0 X 54.0
    Dimensions (WⅹHⅹD) [inch]2.13 x 4.96 x 2.13
    Weight [g]855.00
    Weight [oz]30.16
    Gear Ratio501.9 : 1
    Command SignalDigital Packet
    Protocol TypeHalf duplex Asynchronous Serial Communication (8bit, 1stop, No Parity)
    Link (Physical)RS485 Multi Drop Bus
    ID0 ~ 252
    FeedbackPosition, Velocity, Current, Temperature, Voltage, External Port, etc
    Protocol version2.0
    Operating Mode / AngleTorque Control Mode
    Velocity Control Mode
    Position Control Mode
    Extended Position Control Mode
    PWM Control Mode
    Output [W]200
    Standby Current [mA]40


    354,200円
    在庫数 : 0
  • FRP42-A110K Set(42mm角シリーズ用アダプター)[903-0219-100]
    FRP42-A110K Set(42mm角シリーズ用アダプター)[903-0219-100]
    DYNAMIXEL PRO 42mm角シリーズ対応アルミ製アダプター。


    ■概要:
    DYNAMIXEL PROの高出力に対応した、アルミ削り出しの高剛性、高精度部品です。
    DYNAMIXEL PRO同士の連結や、ヒンジ部品(サーボアーム)との組み合わせで関節を構成することが出来ます。

    ■内容:
    1)アルミ製アダプター本体(黒): 1個
    2)M3×8キャップボルト :20本

    ■対応機種:
    -DYNAMIXEL PRO H42-20-S300-R (ハイエンド/20W/減速比1:300/RS-485)
    -DYNAMIXEL PRO M42-10-S260-R (ミドルクラス/10W/減速比1:260/RS-485)
    -DYNAMIXEL PRO L42-10-S300-R (普及型/10W/減速比1:300/RS-485)

    ■技術情報:


    5,852円
    注文数:
  • FRP54-H121K Set(54mm角対応ヒンジ/100シリーズ/ショート)[903-0215-101]
    FRP54-H121K Set(54mm角対応ヒンジ/100シリーズ/ショート)[903-0215-101]
    DYNAMIXEL PRO 54mm角シリーズ対応アルミ製ヒンジ(サーボアーム)

    ■概要:
    DYNAMIXEL PROでの関節構成用ヒンジ(サーボアーム)です。両持ち支持構造で使用する場合には別売のアイドラー(フリーホーン)と組み合わせます。

    54mm角シリーズの長手寸法が短いモデル(H54-100互換サイズ)対応です。

    ■内容:
    1)アルミ製ヒンジ(黒、2パーツ): 1セット
    2)M3×8キャップボルト :20本

    ■対応機種:
    【アクチュエータ】
    -DYNAMIXEL PRO H54-100-S500-R (ハイエンド/100W/減速比1:500/RS-485)
    -DYNAMIXEL PRO M54-40-S250-R (ミドルクラス/40W/減速比1:250/RS-485)
    -DYNAMIXEL PRO L54-50-S500-R (普及型/50W/減速比1:300/RS-485)
    -DYNAMIXEL PRO L54-50-S290-R (普及型/50W/減速比1:290/RS-485)
    -DYNAMIXEL PRO L54-30-S500-R (普及型/30W/減速比1:500/RS-485)
    -DYNAMIXEL PRO L54-30-S400-R (普及型/30W/減速比1:400/RS-485)

    【アイドラー】

    12,529円
    注文数:
  • FRP42-H221K Set[903-0237-101]
    FRP42-H221K Set[903-0237-101]
    FRP42-H221K Set[903-0237-101]
    Features

    Aluminum hinge frame for DYNAMIXE-P(PM42-010-S260-R).

    Has high strength due to metal processing, and therefore it does not bend or break easily.


    Package Components
    FRP42-H221K1
    Wrench Bolt(WB M3x8)20
    Caution

    Idler Bearing Set (FRP42-I110K Set) required to assemble on the DYNAMIXEL-P.

    Please purchase separately.


    Compatible with PM42-010-S260-R.

    13,508円
    在庫数 : 100
    注文数:
  • FRP42-H121K Set[903-0217-101]
    FRP42-H121K Set[903-0217-101]
    FRP42-H121K Set[903-0217-101]
    Features

    Optional Aluminum Hinge frame for DYNAMIXEL-P(PH42-020-S300-R).


    Has high strength due to metal processing, and therefore it does not bend or break easily

    Package Components
    FRP42-H121K (Black)1
    Wrench Bolt WB M3x820
    Caution

    Idler Bearing Set (FRP42-I110K Set) required to assemble on the DYNAMIXEL-P.


    Please purchase separately.


    Compatible with PH42-020-S300-R.

    15,169円
    在庫数 : 100
    注文数:
  • YM070-210-M001-RH[902-0198-000]
    YM070-210-M001-RH[902-0198-000]
    YM070-210-M001-RH[902-0198-000]受注生産(約2か月)お問い合わせください。
    YM070-210-M001-RH

    24V / 0.3Nm / 4,583rpm / BLDC / RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderCompact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM070-210-M001-RHは減速機を含まず、目的に応じて減速機、リニアアクチュエータ、サーボシリンダーなど様々な製品と組み合わせて使用することができます。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specification

    上の画像は理解を助けるためにレデューサーを含めた分解図です。本製品には減速機は含まれておりません。

    パッケージ構成
    ProductsQty.Note
    YM070-210-M001-RH1DYNAMIXEL-Y(M-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M2X610For output shaft assembly
    Wrench Bolt WB M3x810For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    173,558円
    在庫数 : 0
  • YM070-210-R051-RH[902-0199-000]
    YM070-210-R051-RH[902-0199-000]
    YM070-210-R051-RH[902-0199-000]受注生産(約2か月)お問い合わせください。
    YM070-210-R051-RH

    24V / 8.2Nm/ 39.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder /

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM070-210-R051-RHは、DYNAMIXEL DRIVE (DYD) DYD-14H-051モデルのサイクロイド減速機を内蔵したオールインワンロボットアクチュエータです。

    DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM070-210-R051-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M3X1010For shaft assembly
    Wrench Bolt WB M3x1510For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    292,116円
    在庫数 : 0
  • YM070-210-R099-RH[902-0200-000]
    YM070-210-R099-RH[902-0200-000]
    YM070-210-R099-RH[902-0200-000]受注生産(約2か月)お問い合わせください。
    YM070-210-R099-RH

    24V / 14.6Nm / 20.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM070-210-R099-RHは、DYNAMIXEL DRIVE (DYD) DYD-14H-099モデルのサイクロイド減速機を内蔵したオールインワンロボットアクチュエータです。DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM070-210-R099-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M2X610For output shaft assembly
    Wrench Bolt WB M3x810For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    292,116円
    在庫数 : 0
  • YM080-230-M001-RH[902-0201-000]
    YM080-230-M001-RH[902-0201-000]
    YM080-230-M001-RH[902-0201-000]受注生産(約2か月)お問い合わせください。
    YM080-230-M001-RH

    24V / 0.6Nm/ 2,292rpm / BLDC/ RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderCompact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM080-230-M001-RHには減速機は含まれておりませんので、減速機など様々な製品と組み合わせてご利用いただけます、リニアアクチュエータ・サーボシリンダなど、用途に応じて様々な製品との組み合わせが可能です。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specification

    上の画像は理解を助けるためにレデューサーを含めた分解図です。本製品には減速機は含まれておりません。

    パッケージ構成
    ProductsQty.Note
    YM080-230-M001-RH1DYNAMIXEL-Y(M-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M2.5X810For shaft frame assembly
    Wrench Bolt WB M3x810For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    198,000円
    在庫数 : 0
  • YM080-230-R051-RH[902-0202-000]
    YM080-230-R051-RH[902-0202-000]
    YM080-230-R051-RH[902-0202-000]受注生産(約2か月)お問い合わせください。
    YM080-230-R051-RH

    24V / 15.8Nm / 39.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM080-230-R051-RHは、DYNAMIXEL DRIVE (DYD) DYD-17H-051モデルのサイクロイダル減速機を内蔵したオールインワンロボットアクチュエータです。

    DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM080-230-R051-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M3X2010For output shaft assembly
    Wrench Bolt WB M4x1010For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    326,337円
    在庫数 : 0
  • YM080-230-R099-RH[902-0203-000]
    YM080-230-R099-RH[902-0203-000]
    YM080-230-R099-RH[902-0203-000]受注生産(約2か月)お問い合わせください。
    YM080-230-R099-RH

    24V / 26Nm / 20.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM080-230-R099-RHは、DYNAMIXEL DRIVE (DYD) DYD-17H-099モデルのサイクロイダル減速機を内蔵したオールインワンロボットアクチュエータです。DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM080-230-R099-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M3X2010For output shaft assembly
    Wrench Bolt WB M4x1010For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    326,337円
    在庫数 : 0
  • YM070-210-B001-RH[902-0204-000]
    YM070-210-B001-RH[902-0204-000]
    YM070-210-B001-RH[902-0204-000]受注生産(約2か月)お問い合わせください。
    YM070-210-B001-RH

    24V / 0.3Nm / 4,583rpm / BLDC / RS-485 / Multi-turn encoder / Brake

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Electric Brake for SafetyCompact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM070-210-B001-RHには減速機が含まれておらず、用途に応じて減速機、リニアアクチュエータ、サーボシリンダーなどのさまざまな製品と組み合わせて使用することができます。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specification

    上の画像は理解を助けるためにレデューサーを含めた分解図です。本製品には減速機は含まれておりません。

    パッケージ構成
    ProductsQty.Note
    YM070-210-B001-RH1DYNAMIXEL-Y(M-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M2X610For output shaft assembly
    Wrench Bolt WB M3x810For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続されていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    204,490円
    在庫数 : 0
  • YM070-210-A051-RH[902-0205-000]
    YM070-210-A051-RH[902-0205-000]
    YM070-210-A051-RH[902-0205-000]受注生産(約2か月)お問い合わせください。
    YM070-210-A051-RH

    24V / 8.2Nm/ 39.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder / Brake

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Electric Brake for SafetyIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM070-210-A051-RHは、DYNAMIXEL DRIVE (DYD) DYD-14H-051モデルのサイクロイド減速機を内蔵したオールインワンロボットアクチュエータです。

    DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM070-210-A051-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M3X1010For shaft assembly
    Wrench Bolt WB M3x1510For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    326,810円
    在庫数 : 0
  • YM070-210-A099-RH[902-0206-000]
    YM070-210-A099-RH[902-0206-000]
    YM070-210-A099-RH[902-0206-000]受注生産(約2か月)お問い合わせください。
    YM070-210-A099-RH

    24V / 14.6Nm / 20.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder / Brake

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Electric Brake for SafetyIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM070-210-A099-RHは、DYNAMIXEL DRIVE (DYD) DYD-14H-099モデルのサイクロイド減速機を内蔵したオールインワンロボットアクチュエータです。DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM070-210-A099-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M2X610For output shaft assembly
    Wrench Bolt WB M3x810For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    326,810円
    在庫数 : 0
  • YM080-230-B001-RH[902-0207-000]
    YM080-230-B001-RH[902-0207-000]
    YM080-230-B001-RH[902-0207-000]受注生産(約2か月)お問い合わせください。
    YM080-230-B001-RH

    24V / 0.6Nm / 2,597rpm / BLDC/ RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Electric Brake for SafetyCompact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM080-230-B001-RHには減速機は含まれておりませんので、減速機など様々な製品と組み合わせてご利用いただけます、リニアアクチュエータ・サーボシリンダなど、用途に応じて様々な製品との組み合わせが可能です。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specification

    上の画像は理解を助けるためにレデューサーを含めた分解図です。本製品には減速機は含まれておりません。

    パッケージ構成
    ProductsQty.Note
    YM080-230-B001-RH1DYNAMIXEL-Y(M-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M2.5X810For shaft frame assembly
    Wrench Bolt WB M3x814For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    229,617円
    在庫数 : 0
  • YM080-230-A051-RH[902-0208-000]
    YM080-230-A051-RH[902-0208-000]
    YM080-230-A051-RH[902-0208-000]受注生産(約2か月)お問い合わせください。
    YM080-230-A051-RH

    24V / 15.8Nm / 39.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Electric Brake for SafetyIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM080-230-A051-RHは、DYNAMIXEL DRIVE (DYD) DYD-17H-051モデルのサイクロイダル減速機を内蔵したオールインワンロボットアクチュエータです。

    DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM080-230-A051-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M3X2010For output shaft assembly
    Wrench Bolt WB M4x1010For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    362,120円
    在庫数 : 0
  • YM080-230-A099-RH[902-0209-000]
    YM080-230-A099-RH[902-0209-000]
    YM080-230-A099-RH[902-0209-000]受注生産約2か月につきお問い合わせください。
    YM080-230-A099-RH

    24V / 15.8Nm / 39.2rpm / BLDC / Cycloid / RS-485 / Multi-turn encoder

    Product FeaturesHigh Performance Frameless motorMulti-turn Absolute EncoderIntegrated Electric Brake for SafetyIntegrated Dynamixel Drive(DYD)Compact & Simple Design with Hollow ShaftDynamic Motor Controller商品説明

    YM080-230-A099-RHは、DYNAMIXEL DRIVE (DYD) DYD-17H-099モデルのサイクロイダル減速機を内蔵したオールインワンロボットアクチュエータです。DYNAMIXEL DRIVE (DYD)は、製品購入後に交換することはできません。

    特徴中空シャフトを持つ高性能フレームレスモーター電流検出に基づくトルク制御位置、速度の信頼性と精度を向上させるPID制御統合された絶対磁気エンコーダーと交換可能なバッテリーにより、完全な電源オフ後もマルチターン位置情報を保持(バックアップバッテリー付き)高耐久性のための金属製ハウジングモジュラー構成により、自由度の異なるアプリケーションを簡単に作成可能DYNAMIXEL-Y Ordering Specificationパッケージ構成
    ProductsQty.Note
    YM080-230-A099-RH1DYNAMIXEL-Y(R-option)
    Robot Cable-2P-X4P 600mm(Convertible)1RS485 2P-4P Cable(MOLEX-JST)
    Robot Cable-2P 600mm1RS485 2P Cable(MOLEX-MOLEX)
    Cord End Terminal4For power connection
    Terminal Plug2For power connection
    Wrench Bolt WB M3X2010For output shaft assembly
    Wrench Bolt WB M4x1010For frame assembly
    マルチターンバックアップバッテリーの接続方法Multi-turn Backup Battery Connection

    出荷時はマルチターンバックアップバッテリーは本体に接続れていませんのでご注意ください。
    使用前にマルチターンバックアップバッテリーを本体に接続して、初期化を行ってください。

    電源をDYNAMIXEL-Yから切り、バッテリーカバーのロッキングボルトを緩めます。バッテリーカバーを開けます。バッテリーケーブルを接続します。バッテリーカバーを再度取り付けます。バッテリーカバーのロッキングボルトを締めて固定します。DYNAMIXEL Wizard 2.0を実行し、バッテリー交換手順に従います。詳細については、e-Manualを参照してください。図面

    図面のダウンロード

    drawing組立ガイド
    362,120円
    在庫数 : 0
  • DYD-11-033[902-0164-000]
    DYD-11-033[902-0164-000]
    DYD-11-033納期はお問い合わせください.。

    小型・高耐久のサイクロイド減速機 | 外形43mm角 | 速度伝達比33

    96,800円
    在庫数 : 0
  • TURTLEBOT3 Burger RPi4 2GB (ACアダプター付属) [901-0118-502]
    TURTLEBOT3 Burger RPi4 2GB (ACアダプター付属) [901-0118-502]
    TURTLEBOT3 Burger RPi4 2GB (ACアダプター付属)  [JP1-0118-502]
    本商品にはLinuxとROSのある程度の知識が必要です。
    安定化電源SMPS AKA-12070(12V 7A)[JP3-0043-000]付属
    TURTLEBOT3 Burger
    TurtleBot3(タートルボット3)はROS1,ROS2入門のためのLiDARを搭載したオープンソースの移動ロボットプラットフォームです。
    無償公開のeマニュアル(Webドキュメント、チュートリアル)とサンプルプログラムによりROS1,ROS2の最新バージョンのインストールと学習・評価、応用開発が可能です。



    TurtleBot公式ページ
    TurtleBot3 - ROS wiki
    注意事項組立キット
    この商品は、ユーザー自身による組み立てが必要です。
    必要な工具は同梱されています。はんだ付けの必要は無いです。
    88,550円
    在庫数 : 0
  • TURTLEBOT3 Waffle Pi RPi4 4GB [JP] (ACアダプター付属) [901-0119-502]
     TURTLEBOT3 Waffle Pi RPi4 4GB [JP] (ACアダプター付属) [901-0119-502]
    TURTLEBOT3 Waffle Pi RPi4 4GB [JP] (ACアダプター付属) [901-0119-502]
    本商品にはLinuxとROSのある程度の知識が必要です。
    TurtleBot3(タートルボット3)はROS1,ROS2入門のためのLiDARを搭載したオープンソースの移動ロボットプラットフォームです。
    無償公開のeマニュアル(Webドキュメント、チュートリアル)とサンプルプログラムによりROS1,ROS2の最新バージョンのインストールと学習・評価、応用開発が可能です。



    TurtleBot公式ページ
    TurtleBot3 - ROS wiki
    注意事項組立キット
    この商品は、ユーザー自身による組み立てが必要です。
    必要な工具は同梱されています。はんだ付けの必要は無いです。
    【対応ROSバージョン】
    ROS1 : Kinetic, Melodic, Noetic
    ROS2 : Dashing, Foxy,



    215,050円
    注文数:
  • TURTLEBOT3 Waffle Pi RPi4 2GB [JP] (ACアダプター付属) [901-0119-503]
    TURTLEBOT3 Waffle Pi RPi4 2GB [JP] (ACアダプター付属) [901-0119-503]
    TURTLEBOT3 Waffle Pi RPi4 2GB [JP] (ACアダプター付属) [901-0119-503]
    本商品にはLinuxとROSのある程度の知識が必要です。
    安定化電源SMPS AKA-12070(12V 7A)[JP3-0043-000]付属
    TurtleBot3(タートルボット3)はROS1,ROS2入門のためのLiDARを搭載したオープンソースの移動ロボットプラットフォームです。
    無償公開のeマニュアル(Webドキュメント、チュートリアル)とサンプルプログラムによりROS1,ROS2の最新バージョンのインストールと学習・評価、応用開発が可能です。



    TurtleBot公式ページ
    TurtleBot3 - ROS wiki
    注意事項組立キット
    この商品は、ユーザー自身による組み立てが必要です。
    必要な工具は同梱されています。はんだ付けの必要は無いです。
    【対応ROSバージョン】ROS1 : Kinetic, Melodic, Noetic
    ROS2 : Dashing, Foxy,



    215,050円
    在庫数 : 0
  • TurtleBot3 MM Gen3[JP5-0010-003]
    TurtleBot3 MM Gen3[JP5-0010-003]
    TurtleBot3 MM Gen3 受注生産につきお問い合わせください。

    ROS1、ROS2対応 小型モバイルマニピュレーター、組立完成品


    ROS World 2020: ROBOTIS TurtleBot3 Parallel Session - Open Manipulator-X on the TurtleBot3 from Open Robotics on Vimeo.


    概要組立完成品、国内組立OpenMANIPULATOR-Xは、ROS対応マニピュレーターの1つであり、TurtleBot3 Waffle Piにボルトオンで搭載することでモバイルマニピュレーターを構成できます。これにより、TurtleBot3のSLAMおよびナビゲーション機能等を備えたROS対応サービスロボットプラットフォームとして利用できます。TurtleBot3 MM Gen3は、耐久性と運用の利便性を向上させるために従来モデルよりもバッテリー容量が増大されており、搭載コンピュータとLiDARの性能が向上しています。
    主な仕様
    搭載コンピュータRaspberry Pi 4GB
    対応ROSバージョン(OS)ROS1 Noetic (Ubuntu20.04LTS)
    ROS2 Foxy (Ubuntu 20.04LTS)
    ※ロボット搭載コンピュータと同じバージョンのROSをセットアップしたリモートPC(ネイティブ環境推奨)が別途必要です。

    >>>以前のモデルとの仕様の差分セット内容
    1TurtleBot3 MM Gen3(完成品)本体1台
    2Raspberry Pi 4 4GB1台(本体に装着済)
    3microSDカード 32GB1枚
    4LiDAR LDS-021台(本体に装着済)
    5Raspberry Pi カメラモジュール V2.11台(本体に装着済)
    6UART Bluetoothモジュール BT-410 set(Master/Slave ペアリング済)1セット(MasterはRC-100Bに装着済、Slaveは本体に装着済)
    7ゲームパッド型無線コントローラ RC-100B1台
    8ACアダプター SMPS AKA-12070(12V 7A)1個
    910.8V 5800mAh モバイルバッテリー1台(本体に装着済)
    10モバイルバッテリー専用充電器1個
    11RC-100B用乾電池2本
    12ドライバー、レンチ等作業工具1式
    13保守用ねじ類、予備配線、グリッパー用予備ラバーパッド等1式
    14プラスチック製収納ケース1個
    15クイックスタートガイド1冊

    技術情報Coming soon
    442,750円
    在庫数 : 0
  • TB3 Waffle Plate-IPL-01 (8ea)[903-0259-000]
    TB3 Waffle Plate-IPL-01 (8ea)[903-0259-000]

    [903-0259-000] TB3 Waffle Plate-IPL-01 (8ea)

     ■ Description

     TurtleBot3 Plate

    Can connect various devices by using bolts.

    Can connect 6mm plates by using rivets.

    TurtleBot3 can be modified into various shapes as the plates can be assembled in various directions.

    Does not break easily as it is made of engineering plastic.

     ■ Basic Components

    Components

    Quantity

    Frame

    TB3 Waffle Plate-IPL-01

    8

    Screw

    PHS M3x8K

    20

    Screw

    NUT M3

    30

     ■ How to Use

     

    WafflePlate.jpg

    ■ Compatible Products

     Dynamixel X430 series

    6mm parts (Dream/Smart sets)

     

    ■ Hyperlinks

     Download Drawing : Click Here

    3D Printing STL File : Click Here

     

    Download Assembly Guide : TurtleBot3 Burger
    Download Assembly Guide : TurtleBot3 Waffle


    2,233円
    注文数:
  • Turtlebot3 Big Wheel[JP7-2405-300]
    Turtlebot3 Big Wheel[JP7-2405-300]
    Turtlebot3 Big Wheel[JP7-2405-300]
    お問合せフォームよりお問合せください。
    Turtlebot3 Big Wheel
    Turtlebot3 Friends:Custom Model by ROBOTIS Japan
    構成structure size仕様
    ItemsBig Wheel
    Maximum translate velocity0.48 m/s
    Maximum rotational velocity3.28 rad/s
    Size (L x W x H)281 mm x 318 mm x 175.5 mm
    Weight (+ SBC + Battery + Sensors)2.5 kg
    SBC (Single Board Computer)Raspberry Pi 4 Model B
    Microcontroller boardOpenCR 1.0
    Actuator for WheelsDYNAMIXEL XM430-W210-T
    LiDARLDS-02
    Mobile BatteryUGREEN Power Bank 145W (25000mAh)
    0円
    在庫数 : 0
  • Pi-Camera Frame Set[903-0273-000]
    Pi-Camera Frame Set[903-0273-000]

    Pi-Camera Frame Set[903-0273-000]

    Feature

    This frame is used to mount the Raspberry Pi Camera onto the TurtleBot3 or OpenManipulator. 

    Screws required to mount on the camera and robot are included in the package. 



    Package Components

    Pi-Camera Frame

    1

    PHS M2.5x12

    5

    PHS M2x6

    5

    NUT M2.5

    5

    NUT M2

    5

    Spacer

    5


    *Raspberry Pi Camera NOT included in the package.

    Please use the camera included in your TurtleBot3 package or purchase separately. 


    Caution

    Please be sure to assembly the cable onto the camera first THEN assembly the camera and frame.

    Be sure to keep the cables organized to prevent damages. 


    1893207946_e819e77f_2.png




    1893207946_910c959d_1.png



    1,958円
    注文数:
  • TB3 PCB Support-IBB-01 (12ea)[903-0261-000]
    TB3 PCB Support-IBB-01 (12ea)[903-0261-000]

    [903-0261-000] TB3 PCB Support-IBB-01 (12ea)

     ■ Description

    TurtleBot3 Support that can connect various devices

    Can be used to connect parts which do not fit the hole spacing of the Waffle plate.

    Does not break easily as it is made of engineering plastic.

    ■ Basic Components 

    Components

    Quantity

    Frame

    TB3 PCB Support

    12

    Screw

    PHS M2x8

    10

    Screw

    PHS M2.5x8K

    10

    Screw

    NUT M2

    10

    Screw

    NUT M2.5

    10

     ■ How to Use

    PCBSupport.jpg

    ■ Compatible Products

    Dynamixel X430 series (Can be attached to the horn)

    6mm parts (Dream/Smart sets)

     

    ■ Hyperlinks

    Download Drawing : Click Here

    3D Printing STL File : Click Here

    Download Assembly Guide : TurtleBot3 Burger

    Download Assembly Guide : TurtleBot3 Waffle



    836円
    在庫数 : 94
    注文数:
  • TB3 Wheel/Tire Set-ISW-01 (2ea)[903-0260-000]
    TB3 Wheel/Tire Set-ISW-01 (2ea)[903-0260-000]

    [903-0260-000] TB3 Wheel Tire Set-ISW-01 (2ea)

     ■ Description

    TurtleBot3 Wheel Tire Set

    Can be attached to the Dynamixel by using bolts.

    Does not break easily as it is made of engineering plastic.

    Rubber tires with high grip force have been applied.

    Can be used to make caterpillars, etc. instead of rubber tire.

    ■ Basic Components

    Components

    Quantity

    Wheel

    TB3 Wheel

    2

    913-3018-000

    Tire_2 (TR-66)

    2

    Screw

    PHS M2x4K

    20

    ■ How to Use

     

    WheelTire-ISW.jpg

    ■ Compatible Products

    Dynamixel X430 series (Can be attached to the horn)

    Dynamixel AX series

    Dynamixel RX-28, MX-28

    12mm parts

    ■ Hyperlinks

     Download Drawing : Click Here

    3D Printing STL File : Click Here


    Download Assembly Guide : TurtleBot3 Burger

    Download Assembly Guide : TurtleBot3 Waffle


    1,122円
    注文数:
  • TB3 Ball Caster-A01 (1ea)[903-0262-000]
    TB3 Ball Caster-A01 (1ea)[903-0262-000]

    [903-0262-000] TB3 Ball Caster-A01 (1ea)

      

    ■ Description

    TurtleBot3 Ball Caster

    Compatible with 6mm plate and can be connected to the TB3 Waffle Plate.

      

    ■ Basic Components 

    Components

    Quantity

    Frame

    TB3 Ball Caster (Frame Steel Ball)

    1

    Screw

    PHS M2x6 TAP-K

    5

    Rivet

    Rivet (SRV-1I)

    5

     

     

    ■ How to Use

    BallCaster-A01_1.png

     

     

    ■ Compatible Products

    TB3 Waffle Plate IPL-01

    6mm parts

      

    ■ Hyperlinks 

    Download Drawing : Click Here

    3D Printing STL File : Click Here

    Download Assembly Guide : TurtleBot3 Burger

    Download Assembly Guide : TurtleBot3 Waffle



    363円
    注文数:
  • TB3 Caterpillar-ICT-01 (40ea)[903-0271-000]
    TB3 Caterpillar-ICT-01 (40ea)[903-0271-000]

    [903-0271-000] TB3 Caterpillar-ICT-01 (40ea)

      

    ■ Description 

    TurtleBot3 Caterpillar parts

    Can be used with TB3 Wheel after assembling all the Caterpillar parts.

    For more details, please refer to the TurtleBot3 Friends (Tank).

      

    ■ Basic Components 

    Components

    Quantity

    Frame

    TB3 Caterpillar-ICT-01

    40

    * TB3 Wheel on the image is not included

      

    ■ How to Use

     TB3-Caterpillar-ICT-01_3.jpg


    * The color in this image has been changed for identification. The actual color is black.

      

    ■ Hyperlinks

    STL Drawing : Click here


    1,848円
    注文数:
  • RM-X52-TNM[905-0024-000]
    RM-X52-TNM[905-0024-000]

    RM-X52-TNM[905-0024-000]
    売れています。TUTLEBOT用に開発されたROS対応MANIPULATORです。
    運用には架台のBASEPLATE-02
    インターフェースのU2D2
    電源供給基板のU2D2 PHB Set
    安定化電源SMPS等がお勧めです。

    Feature

    This product is a compact version of OpenManipulator based on ROS.


    It has a high payload as DYNAMIXEL XM-430 model is applied.  

    Easy to use with PC or mobile platform such as TB3 Waffle Pi. 

    Provides source code and development environment which helps you immediately operate it with TB3 Waffle Pi

    You can freely select and use either PC or Controller e.g. OpenCR.

    Provides a variety of open source software as well as 3D drawings and CAD data for research and development.


    RM-X52-TNM-구성.jpg


    Package Component

    XM430-W350-T

    5

    Exclusive Plastic Frame Set

    1

    FR12-H101K

    2

    FR12-H104K

    1

    FR12-S101K

    1

    FR12-S102K

    2

    HN12-I101 Set

    3

    HN11-I101 Set (spare)

    3

    Robot Cable Set X3P (by length)

    5

    Bolt & Nut Set

    1

    Rubber Pad (Finger Tip)

    2 types x 2

    Phillips Screwdriver

    1

    Allen Wrench (by type)

    3


    H/W Specification


    DYNAMIXEL

    XM430-W350-T

    Power Supply (sold separately)

    12V

    Freedom of degree

    5 (4DOF 1DOF Gripper)

    Payload

    500g

    RPM (joint)

    46RPM

    Weight (assembly)

    700g

    Length

    380mm

    Gripper stroke

    20~75mm

    Interface

    TTL Level Multi Drop BUS

    Software

    ROS. DYNAMIXEL SDK, Arduino, Processing

    Controller (sold separately)

    PC, OpenCR

    RM-X52_CAD_2D.JPG


    Various Applications

    RM-X52-TNM-응용.jpg


    Sold Seperately


    Power Supply

    SMPS 12V 5A

    Controller

    OpenCR or PC

    Interface

    U2D2

    Etc.

    Base Plate-02



    Caution

    DYNAMIXEL, power supply, and controller are not included.
    Please purchase separately. 


    Compatible with TB3 controller and power.


    The assembly Manuel is not included, but you can download the pdf file on online for free. (Refer to below link)

    The necessary idler set (HN11-I101 Set) is included in case you would like to use DYNAMIXEL XL430 as a hinge.
    (* Need to purchase DYNAMIXEL XL430 separately)


    Package Contents
    RM-X52-TNM_partslist.jpg


    Assembly Manuel - LINK

    Drawing (OnShape) - LINK

    Drawing (
    Thingiverse) - LINK

    Source Code - LINK

    ROS WIKI - LINK


    180,895円
    在庫数 : 0
  • RM-X52 Frame Set[905-0023-000]
    RM-X52 Frame Set[905-0023-000]

    RM-X52 Frame Set[905-0023-000]
    TURTLEBOT用に開発されたMANIPULATORのフレームセットです。

    Feature

    This product is a frame set which can make X430 based OpenManipulator.


    You can assemble an OpenManipulator (4 DOF Arm 1 DOF Gripper), which is the same as OpenManipulator 
    (RM-X52).


    DYNAMIXEL X430 is not included so you can select a suitable DYNAMIXEL model considering payload.

    XH430, XM430 and XL430 are all compatible with this frame and can be also mixed.

    Both the idler set and the assembly tool for hinge frame assembly are all included.

    You can make an OpenManipulator with your desired specification and can fix it on Base Plate-02 or attach it to TB3 Waffle Pi.




    Package Component

    Exclusive Plastic Frame Set

    1

    FR12-H101K

    2

    FR12-H104K

    1

    FR12-S101K

    1

    FR12-S102K

    2

    HN12-I101 Set

    3

    HN11-I101 Set

    3

    Robot Cable Set X3P (by length)

    5

    Bolt & Nut Set

    1

    Rubber Pad (Finger Tip)

    2 types x 2

    Phillips Screwdriver

    1

    Allen Wrench (by type)

    3



    Caution


    DYNAMIXEL, power supply, and controller are not included.
    Please purchase separately. 

    When selecting DYNAMIXEL X430 model, the appropriate model should be selected considering communication method and target specification (payload).


    XL430 Single-model configuration is not recommended as it might be short of output.

    When mixing XL430 with XH / XM430, they (XH / XM430) must be TTL communication model.


    When you use XH430-V-series (24V model), you must configure your OpenManipulator as a single 24V model.

    AX / MX series, X540 series, and PRO series cannot be used.

    The Assembly Manuel is not included, but you can download the pdf file on online for free. (Refer to below link)



    Package Contents


    RM-X52-FrameSet_partlist.jpg

    Drawing (OnShape) - LINK

    Drawing (Thingiverse) - LINK

    Assembly Manuel - LINK


    37,576円
    注文数:
  • Base Plate-02[905-0026-000]
    Base Plate-02[905-0026-000]
    Base Plate-02[905-0026-000]
    OpenManupulator(RM-X52)用の作業プレートです。

    Feature


    Base Plate-02 is made of aluminum and used for fixing OpenManupulator(RM-X52)

    Can be used to install a manipulator on a table.

    It can be fixed with a clamp. (Clamp is not included in this package)





    Package Component

    Base Plate-02

    1

    Wrench Bolt M2.5x20

    6

    Spacer

    6


    H/W Specification


    Size (mm)

    300 x 300 x 10

    Weight (kg)

    2.5



    How To Assemble

    BasePlate-02_Assemble.jpg



    Caution

    Only DYNAMIXEL X430 series can be assembled.

    AX/MX-series, X540-series, and PRO-series cannot be used.



    Includes screws and spacer rings in order to fix DYNAMIXEL to Base Plate-02


    When assembling XL430, you can use the circular spacer ring included in this package, or use the oval spacer included in XL430 package.





    Drawing - LINK

    25,300円
    注文数:
1 2 3 45 6 7 8 9 次へ >>

(全商品:430点)

表示件数: