(全商品:430点)
The U2D2 Power Hub Board combines with the U2D2 to supply a variety of external power sources to DYNAMIXELs.
The board is capable of supplying power to all DYNAMIXELs with the SMPS port, terminal block, and 2P power connector.
The board has holes to fix the U2D2 module and can be assembled using the rivets supplied in the package.
-Easily powers ON/OFF with the power switch
*Robot cable for connecting U2D2 is included.
- Use the Molex-JST Convertible Cable (Use 3P or 4P based on your communication selection)
DYNAMIXEL X-Series, PRO+ Series
- Use the JST Cable. (Use 3P or 4P based on your communication selection)
**This cable is for DYNAMIXEL XW-Series version only**
This is the waterproof Connector to RS-485 4P cable set for Dynamixel XW-series.
XW540-T260-R
XW540-T140-R
MX-106TやMX-106Rをマスタースレーブモードで使用する場合必要な同期ケーブルです。バルクには付属していませんのでバルク購入でマスタースレーブをする場合必要です。
■ DESCRIPTION
- 3P sync cable set for using dual joint mode in Dynamixel models that support the mode.
- Has strong coating to withstand ripping.
Dual Joints
Dual joints are used as 1 joint by controlling 2 motors simultaneously.
To use the dual joints, 1 unit of motor set in master mode and 1 unit of motor set in slave mode are needed.
Next, the motors must be connected to each other using synchronization cable.
Normal mode synch cable: Drives Master and PWM signals synchronized
Reverse mode synch cable: Drives PWM signals in reverse.
Notes : Slave is synchronized by directly receiving the control command through synchronization cable from Master. Slave Mode unit responds to communication through command packets, but data related to motor drive are processed only through the synchronization.
■ PACKAGE CONTENTS
DESCRIPTION
Qty
Robot Cable
3P-Sync 160mm
5
■ COMPATIBLE PRODUCTS
- DYNAMIXEL : MX-106
■ e-Manual
http://support.robotis.com/en/product/dynamixel/mx_series/mx-106.htm
Lithium-ion rechargeable battery.
PCM is incorporated to protect the battery from overcharge, discharge, and excessive current. Battery cover (blue) included for safety.
* Battery charger (LBB-041) sold separately
Cell type Li-ion 18650
PCM built-in (overcharge, discharge, excessive current protection)
Controller : CM-150/151, OpenCM9.04
Battery Charger : Li-ion Battery Charger Set LBB-040, Li-ion Battery Charger Set LBB-041
- This battery can NOT be connected directly to the controller.
You will need the Li-ion Battery Charger Set (LBB-041) to connect to the controller (robot).
Detach the battery from the robot or controller when storing away.
When storing away the battery for a long time, make sure the battery life is around 50%.
Do not store it in wet or hot places.
※ The warranty for Li-ion Battery 3.7V 2600mAh LB-041 is 6 months.
Caution
- Do not drop or give impact.
- Do not operate while charging.
- Do not apply heat, water or any other liquid on the battery.
- Do not place in the microwave, washing machine or dryer.
- Do not use damaged batteries (inflated, deformed, damaged, etc.).
- Do not short circuit the polarity.
- Do not take the battery apart.
- When charging, make sure the battery is connected to the correct polarity.
- Do not charge when the battery is hot. Please charge after it has cooled off.
- Do not keep the battery connected to the controller when not in use.
※ LB-041(New Li-ion battery) cannot be recharged with LBB-040(Old Li-ion battery charger).
※ LBB-041(New Li-ion battery charger) can be recharged with LB-040(Old Li-ion battery).
This LiPo battery is intended for Engineer Kits.
PCM is incorporated to protect the battery from overcharge, discharge, and excessive current.
Can be recharged with LBC-010 Battery Charger.
Controller : CM-510, CM-530, CM-700, CM-550
Charger : LIPO Battery Charger LBC-010
CM-100, CM-5, CM-2+, CM-150, CM-200 , OpenCM7.0 are not compatible
When storing away the battery for a long time, make sure the battery life is around 50%.Store it out of direct sunlight between 0 and 45 degrees.
Do not store with metal items such as coins, keys, necklaces
※ The warranty for LI-PO Battery 11.1V 1300mAh LB-020 is 6 months.
Do not drop or fold parts of the battery or its parts.
Do not use the product when charging.
Do not apply heat, water or any other liquid on the battery.
Do not place in the microwave, washing machine or dryer.
Do not use damaged batteries. (inflated,deformed, damaged, etc)
Do not short circuit the polarity.
Do not take the battery apart.
When charging, make sure the battery is connected into the correct polarity.
Do not charge when the battery is hot. Please charge after it has cooled off.
When the battery is not being used or fully charged, please do not have it connected to a controller.
Do NOT charge the battery when the battery is connected to the controller.
Little Fuse 125V 10A (LFU-10) 10pcs[903-0178-000]
■ 特徴
- CM-510 / CM-700用のヒューズ
■ 構成品
- ヒューズ : 10個
■ 容量
- 125V 10A
■ 適用可能な製品
- CM-510, CM-700
お問い合わせ